A Beginner's Guide to Installing a Bathtub

Check It Out

Presented here in the next paragraph you will find additional professional insight around How to Install a Bathtub Yourself.

Installing a bath tub isn't precisely brain surgery, yet it does call for solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is conveniently accessible, the task can relocate speedily; if you need to open up a wall surface to get rid of the old tub and also place the brand-new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require a helper to vacate the old bathtub and also embeded in the new one. See to it you have actually qualified yourself for the task and also fit trying it. As opposed to hiring a contractor to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This article will aid you set up a new bathtub in your shower room if you have actually already bought a new tub and don't need to change the plan of your previous water supply pipes.
Your devices and material list must make up the following:

New Bath tub

Hammer

Pipe Wrenches

Prybar

Shatterproof glass

Degree

Pliers

Flexible Wrench

Putty Blade

Screwdriver

Cold Knife

Measuring tape

Pipe Caps

Removing Old Touches

If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of removing the existing taps can be fairly problematic due to the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the remaining water that will originate from the pipes. Once the supply pipes have actually been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before going on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.

Suitable New Taps

If the tails of the brand-new faucets are plastic, then you will require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and the sink. Safeguard the faucet in place with the producer offered backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The former kind ought to be connected to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

Setting up the Bathtub

Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are practical in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small factors.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bathtub up until the level reads degree.
To install faucets, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Turn on the water system and also inspect all joints and also brand-new pipework for leakages and tighten them if necessary. Load the bathtub as well as additionally examine the overflow outlet and the regular outlet for leakages.
Ultimately, repair the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the bathtub ought to wait till the bath tub has been used at the very least once as this will settle it right into its last setting.

Getting ready for the Installation

To start with, the sustaining structure provided with the bath needs to be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets device to stop stress on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its last placement.

Tiling Around the Bathtub

In the location where the bathroom satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, creating the water to pass through the wall between the bathroom and the tiling, bring about complications with moisture as well as possible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and also cartridges, and can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to allow for the motion experienced when the tub is in usage. The sealer can fracture rather very early if you do not think about this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water resistant glue as well as grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you really like reading about How to Install a Bathtub Yourself? Make feedback directly below. We would be glad to know your feelings about this posting. We are looking forward that you come back again before long. Enjoyed our blog entry? Please share it. Help another person check it out. I praise you for your time. Kindly check up our site back soon.

Need fast action?